Dodge 2013 Challenger SRT8 User Manual

Challenger SRT8Chrysler Group LLC OWNER’S MANUAL2013 2013 Challenger SRT813D492-126-AB Second Edition Printed in U.S.A.

Whenever a change is noticed in the sound of the exhaustsystem, when exhaust fumes can be detected inside thevehicle, or when the underside or rear of

feel the air directed against the windshield. See yourauthorized dealer for service if your defroster is inoper-able.Floor Mat Safety InformationAlway

WARNING! (Continued)• If required, mounting posts must be properly in-stalled, if not equipped from the factory.Failure to properly follow floor mat i

UNDERSTANDING THE FEATURES OF YOUR VEHICLECONTENTS䡵 MIRRORS ...106▫ Automatic Dimming Mirror — If Equipped . . .106▫ Outside

▫ Voice Training ...146䡵 SEATS ...146▫ Power Seats ...147▫ Heated Seats — If Equ

䡵 WINDSHIELD WIPERS AND WASHERS ...164▫ Intermittent Wiper System ...165▫ Mist Feature ...166▫ Windshield Washers

䡵 OVERHEAD CONSOLE ...181▫ Courtesy/Reading Lights ...182▫ Sunglasses Storage ...182䡵 GARAGE DOOR OPENER —

䡵 CUPHOLDERS ...199▫ Front Cupholders ...199▫ Rear Cupholders ...200䡵 CONSOLE FEATURES ...

MIRRORSAutomatic Dimming Mirror — If EquippedThis mirror automatically adjusts for headlight glarefrom vehicles behind you. You can turn the feature o

Outside MirrorsTo receive maximum benefit, adjust the outside mirror(s)to center on the adjacent lane of traffic and a slightoverlap of the view obtai

THINGS TO KNOW BEFORE STARTING YOUR VEHICLECONTENTS䡵 A WORD ABOUT YOUR KEYS ...12▫ Wireless Ignition Node (WIN) ...12▫ KeyFob...

Power MirrorsThe power mirror controls are located on the driver’sdoor trim panel. To adjust a mirror, turn the control wandtoward the left or right m

the heated mirrors will still function as intended. Refer to“Rear Window Features” in “Understanding The Fea-tures Of Your Vehicle” for further inform

desired position. To use the extender feature of the sunvisor, grab the extender which is located at the rear of thevisor and pull rearward.Uconnect®

Uconnect® Phone allows you to transfer calls betweenthe system and your mobile phone as you enter or exityour vehicle and enables you to mute the syst

Voice Command ButtonActual button location may vary with the ra-dio. The individual buttons are described in the“Operation” section.The Uconnect® Phon

part of the command when you are asked for it. Forexample, you can use the compound form voice com-mand “Phonebook New Entry”, or you can break thecom

The following are general phone to Uconnect® Phonepairing instructions:• Press thebutton to begin.• After the “Ready” prompt and the following beep, s

• The system will prompt you to say the number youwant to call.• For example, you can say “234-567-8901”.• The Uconnect® Phone will confirm the phone

• Automatic download and update, if supported, beginsas soon as the Bluetooth® wireless phone connection ismade to the Uconnect® Phone, for example, a

• When prompted, enter the number designation (e.g.,“Home”, “Work”, “Mobile”, or “Other”). This willallow you to store multiple numbers for each phone

▫ Programming Additional Transmitters...27▫ Transmitter Battery Replacement ...27▫ General Information ...28䡵REMOTE STAR

After you are finished editing an entry in the phonebook,you will be given the opportunity to edit another entry inthe phonebook, call the number you

Delete/Erase “All” Uconnect® Phonebook Entries• Press the button to begin.• After the “Ready” prompt and the following beep, say“Phonebook Erase All”.

mobile service plan. For example, if your mobile serviceplan provides three-way calling, this feature can beaccessed through the Uconnect® Phone. Chec

Place/Retrieve A Call From HoldTo put a call on hold, press the button until you heara single beep. This indicates that the call is on hold. Tobring t

Redial• Press the button to begin.• After the “Ready” prompt and the following beep, say“Redial”.• The Uconnect® Phone will call the last number thatw

• After the “Ready” prompt and the following beep, saythe name of the language you wish to switch toEnglish, Espanol, or Francais.• Continue to follow

• If supported, this number may be programmable onsome systems. To do this, press thebutton and say“Setup”, followed by “Emergency”.• The Uconnect® Ph

certain companies, which time out a little too soon towork properly with the Uconnect® Phone.Voice Mail CallingTo learn how to access your voice mail,

NOTE:• You may not hear all of the tones due to mobile phonenetwork configurations. This is normal.• Some paging and voice mail systems have system ti

using Uconnect® Phone. The status is given for networksignal strength, phone battery strength, etc.Dialing Using The Mobile Phone KeypadYou can dial a

▫ Supplemental Restraint System (SRS) —Air Bags ...59▫ Air Bag Deployment Sensors And Controls ...65▫ Event Data Recorder (E

from your Uconnect® Phone paired mobile phone to theUconnect® Phone or vice versa, press thebuttonand say “Transfer Call”.Connect Or Disconnect Link B

• The selected phone will be used for the next phonecall. If the selected phone is not available, theUconnect® Phone will return to using the highestp

• Press thebutton and say the “Voice Training”,“System Training”, or “Start Voice Training” com-mand.You can either press the Uconnect® Phone button t

• low road noise,• smooth road surface,• fully closed windows,• dry weather condition.• Even though the system is designed for users speakingin North

• smooth road surface,• fully closed windows,• dry weather conditions, and• operation from the driver’s seat.• Performance, such as audio clarity, ech

Send Messages:You can send messages using Uconnect® Phone. To senda new message:• Press thebutton.• After the “Ready” prompt and the following beep, s

16. Can this wait?17. Bye for now18. When can we meet?19. Send number to call20. Start without meTurn SMS Incoming Announcement ON/OFFTurning the SMS

3UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135

136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

3UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137

A WORD ABOUT YOUR KEYSYour vehicle uses a keyless ignition system. This systemconsists of a Key Fob with Remote Keyless Entry (RKE)transmitter and a W

Voice CommandsPrimary Alternate (s)zeroonetwothreefourfivesixseveneightninestar (*)plus (+)pound (#)add locationVoice CommandsPrimary Alternate (s)all

Voice CommandsPrimary Alternate (s)helphomelanguagelist nameslist phonesmobilemutemute offnew entrynootherpair a phonephone pairing pairingphonebook p

General InformationThis device complies with Part 15 of the FCC rules andRSS 210 of Industry Canada. Operation is subject to thefollowing conditions:•

WARNING!Any voice commanded system should be used onlyin safe driving conditions following all applicablelaws. Your attention should be focused on saf

To hear the first available Menu, press the Voice Com-mandbutton and say “Help” or “Main Menu”.CommandsThe Voice Command system understands two types

Radio AMTo switch to the AM band, say “AM” or “Radio AM”. Inthis mode, you may say the following commands:• “Frequency #” (to change the frequency)• “

Disc ModeTo switch to the disc mode, say “Disc”. In this mode, youmay say the following commands:• “Track” (#) (to change the track)• “Next Track” (to

– “Delete” (to delete the recording)• “Play Memos” (to play previously recorded memos) —During the playback you may press the Voice Com-mandbutton to

Voice TrainingFor users experiencing difficulty with the system recog-nizing their voice commands or numbers the Uconnect®Voice “Voice Training” featu

Power SeatsThe power seat switches are located on the outboard sideof the front seat cushions. The power seat switches areused to control the position

Key FobThe Key Fob operates the ignition switch. Insert thesquare end of the key fob into the ignition switch locatedon the instrument panel and rotat

Power Lumbar — If EquippedVehicles equipped with power driver or passenger seatsare also equipped with power lumbar. The power lumbarswitch is located

WARNING!• Adjusting a seat while driving may be dangerous.Moving a seat while driving could result in loss ofcontrol which could cause a collision and

You can choose from HIGH, LOW or OFF heat settings.Amber indicator lights in each switch indicate the level ofheat in use. Two indicator lights will i

rearward. Release the bar once the seat is in the desiredposition. Using body pressure, move forward and rear-ward on the seat to be sure that the sea

Passenger Seat Easy EntryOn the passenger seat, pull forward on the lever locatedon the side of the seatback in order to dump the seatbackand slide th

Head RestraintsHead restraints are designed to reduce the risk of injuryby restricting head movement in the event of a rearimpact. Head restraints sho

NOTE: The head restraints should only be removed byqualified technicians, for service purposes only. If eitherof the head restraints require removal,

When the seatback is folded to the upright position, makesure it is latched by strongly pulling on the top of theseatback above the seat strap.Folding

WARNING!• Be certain that the seatback is securely locked intoposition. If the seatback is not securely locked intoposition, the seat will not provide

CAUTION!To prevent possible damage, do not slam the hood toclose it. Lower the hood until it is open approxi-mately 6 in (15 cm), and then drop it. Th

To remove the emergency key, slide the mechanical latchat the top of the Key Fob sideways with your thumb andthen pull the key out with your other han

the headlights, parking lights, instrument panel lights,instrument panel light dimming, interior lights and foglights.Rotate the headlight switch cloc

Headlights On With Wipers (Available WithAutomatic Headlights Only)When this feature is active, the headlights will turn onapproximately 10 seconds af

position, the headlights are off and the parking brake isreleased. The headlight switch must be used for normalnighttime driving.If vehicle is equippe

An indicator light in the instrument cluster illuminateswhen the fog lights are turned on.NOTE: The fog lights will operate with the low beamheadlight

Turn SignalsMove the multifunction lever up or down and the arrowson each side of the instrument cluster flash to showproper operation of the front an

Map/Reading LightsThese lights are mounted between the sun visors on theoverhead console. Each light is turned on by pressing thelens. Press the lens

open. This includes the glove box light, but not the trunklight. To restore interior light operation, either place theignition in the RUN position or

Rotate the end of the multifunction lever to the firstdetent past the intermittent settings for low-speed wiperoperation, or to the second detent past

Mist FeatureRotate the end of the lever downward to the Mistposition to activate a single wipe cycle to clear off roadmist or spray from a passing veh

Headlights On With Wipers (Available WithAutomatic Headlights Only)When this feature is active, the headlights will turn onapproximately 10 seconds af

NOTE:The power window switches, radio, power sun-roof (if equipped), and ignition-powered power outlets willremain active for up to 60 minutes after t

To unlock the steering column, push the lever downward(toward the floor). To tilt the steering column, move thesteering wheel upward or downward as de

The heated steering wheel switch is located on the switchbank below the climate controls. There are also soft-keys inthe radio screen that will activa

ELECTRONIC SPEED CONTROL — IF EQUIPPEDWhen engaged, the Electronic Speed Control takes overaccelerator operations at speeds greater than 25 mph(40 km/

NOTE: In order to ensure proper operation, the Elec-tronic Speed Control System has been designed to shutdown if multiple Speed Control functions are

To DeactivateA soft tap on the brake pedal, pushing the CANCELbutton, or normal brake pressure while slowing thevehicle will deactivate Electronic Spe

Using Electronic Speed Control On HillsThe transmission may downshift on hills to maintain thevehicle set speed.NOTE: The Electronic Speed Control sys

ParkSense® SensorsThe four ParkSense® sensors, located in the rear fascia/bumper, monitor the area behind the vehicle that iswithin the sensors’ field

The system will indicate a detected obstacle by showingthree solid arcs and will produce a one-half second tone.As the vehicle moves closer to the obj

The vehicle is close to the obstacle when the EVIC displayshows one flashing arc and sounds a continuous tone.The following chart shows the warning al

WARNING ALERTSRear Distance(in/cm)Greater than79 in (200 cm)79-39 in(200-100 cm)39-25 in(100-65 cm)25-12 in(65-30 cm)Less than12 in (30 cm)Audible Ale

WARNING! (Continued)• Allowing children to be in a vehicle unattended isdangerous for a number of reasons. A child orothers could be seriously or fata

Instrument Panel” for further information. When theshift lever is moved to REVERSE and the system isdisabled, the EVIC will display the “PARK ASSIST S

ParkSense® System Usage PrecautionsNOTE:• Ensure that the rear bumper is free of snow, ice, mud,dirt and debris to keep the ParkSense® system oper-ati

• On vehicles equipped with a tailgate, ParkSense®should be disabled when the tailgate is in the loweredor open position and the vehicle is in REVERSE

WARNING! (Continued)• Before using ParkSense®, it is strongly recom-mended that the ball mount and hitch ball assem-bly is disconnected from the vehic

Courtesy/Reading LightsAt the forward end of the overhead console are twocourtesy/reading lights.Press the lens to turn on the light. Press it a secon

NOTE: HomeLink® is disabled when the Vehicle Secu-rity Alarm is active.Before You Begin Programming HomeLink®Ensure your vehicle is parked outside of

NOTE:• Erasing all channels should only be performed whenprogramming HomeLink® for the first time. Do noterase channels when programming additional bu

1. Turn the ignition switch to the ON/RUN position.2.Place the hand-held transmitter 1 to 3 inches (3 to 8 cm)away from the HomeLink® button you wish

To program the remaining two HomeLink® buttons,repeat each step for each remaining button. DO NOTerase the channels.Reprogramming A Single HomeLink® B

5. Press and hold the programmed HomeLink® button.The EVIC will display “CHANNEL # TRANSMIT”. Ifthe garage door opener/device activates, program-ming

will cause the reminder chime to sound. Refer to “Start-ing Procedures” in “Starting And Operating” for furtherinformation.SENTRY KEY®The Sentry Key®

3. Simultaneously press and hold both the Homelink®button while you press and release (“cycle”), yourhand-held transmitter every two seconds.4. Contin

Using HomeLink®To operate, press and release the programmedHomeLink® button. Activation will now occur for theprogrammed device (i.e., garage door ope

WARNING!• Your motorized door or gate will open and closewhile you are programming the universal trans-ceiver. Do not program the transceiver if peopl

• The term IC before the certification/registration num-ber only signifies that Industry Canada technical speci-fications were met.POWER SUNROOF — IF

WARNING!• Never leave children unattended in a vehicle, anddo not leave the key in the ignition switch (or leavethe ignition of a vehicle equipped wit

position. The sunroof will close fully and stop automati-cally. This is called “Express Close”. During ExpressClose operation, any movement of the swi

Wind BuffetingWind buffeting can be described as the perception ofpressure on the ears or a helicopter-type sound in theears. Your vehicle may exhibit

The front 12 Volt power outlet has power available onlywhen the ignition is placed in the ACC or RUN position.This power outlet will also operate a co

The center console power outlet is powered directly fromthe battery (power available at all times).Items plugged into this power outlet may discharge

WARNING!To avoid serious injury or death:• Only devices designed for use in this type of outletshould be inserted into any 12 Volt outlet.• Do not tou

VEHICLES SOLD IN CANADAWith respect to any Vehicles Sold in Canada, the nameChrysler Group LLC shall be deemed to be deleted and thename Chrysler Cana

CAUTION! (Continued)Use of these systems may result in vehicle startingproblems and loss of security protection.All of the Key Fobs provided with your

CAUTION!• Many accessories that can be plugged in drawpower from the vehicle’s battery even when not inuse (i.e., cellular phones, etc.). Eventually,

CUPHOLDERSFront CupholdersThe front cupholders are located in the center console.Illuminated Front Cupholders — If EquippedThe front cupholders are il

Rear CupholdersThe rear seat cupholders are located in the center armrestbetween the rear seats. The cupholders are positionedforward in the armrest a

Console StorageThe center console has a storage compartment locatedunderneath the armrest, and also contains a 12 Voltpower outlet, a molded-in coin h

WARNING! (Continued)should be stowed while driving. Use of these deviceswhile driving can cause an accident due to distrac-tion, resulting in death or

UNDERSTANDING YOUR INSTRUMENT PANELCONTENTS䡵 INSTRUMENT PANEL FEATURES ...206䡵 INSTRUMENT CLUSTER ...207䡵 INSTRUMENT CLUSTER DESC

䡵 Uconnect® 730N/430/430N CD/DVD/HDD/NAV — If Equipped ...237▫ Operating Instructions(Voice Command System) — If Equipped...237▫ Operat

▫ Controlling The iPod® Or External USBDevice Using Radio Buttons ...266▫ Play Mode ...266▫ List Or Browse Mode ...

INSTRUMENT PANEL FEATURES1 — Air Outlets 6 — ESC OFF Switch 11 — Ignition Switch2 — Instrument Cluster 7 — Sport Button 12 — Trunk Release Button3 — G

INSTRUMENT CLUSTER4UNDERSTANDING YOUR INSTRUMENT PANEL 207

Customer Key ProgrammingProgramming Key Fobs or RKE transmitters may beperformed at an authorized dealer.General InformationThe Sentry Key® system com

INSTRUMENT CLUSTER DESCRIPTIONS1. Fuel GaugeThe pointer shows the level of fuel in the fuel tank whenthe ignition switch is in the ON/RUN position.2.

charging system is experiencing a problem. See yourlocal authorized dealer to obtain service immediately.If jump starting is required, refer to “Jump

CAUTION!Driving with a hot engine cooling system coulddamage your vehicle. If the temperature gauge reads“280“, pull over and stop the vehicle. Idle t

either not on during starting, stays on, or turns on whiledriving, have the system inspected at an authorizeddealer as soon as possible. Refer to “Occ

The ESC system will make buzzing or clicking soundswhen it is active. This is normal; the sounds will stopwhen ESC becomes inactive following the mane

17. Shift Lever Indicator — Automatic TransmissionOnlyThe Shift Lever Indicator is self-contained within theinstrument cluster. It displays the gear p

20. Brake Warning LightThis light monitors various brake functions,including brake fluid level and parking brakeapplication. If the brake light turns

Brake Warning Light will turn on along with the ABSLight. Immediate repair to the ABS system is required.Operation of the Brake Warning Light can be c

one or more of your tires is significantly under-inflated.Accordingly, when the low tire pressure telltale illumi-nates, you should stop and check you

CAUTION! (Continued)equipped on your vehicle. Undesirable system opera-tion or sensor damage may result when using re-placement equipment that is not

To Arm The SystemFollow these steps to arm the Vehicle Security Alarm:1. Remove the key from the ignition system (refer to⬙Starting Procedures⬙ in ⬙St

start. If the MIL does not come on when turning the keyfrom OFF to ON/RUN, have the condition checkedpromptly.Certain conditions, such as a loose or m

This system conveniently allows the driver to select avariety of useful information by pressing the switchesmounted on the steering wheel. The EVIC co

The system allows the driver to select information bypressing the following buttons mounted on the steeringwheel:MENU ButtonPress and release the MENU

Press and hold the SELECT button for two seconds toreset features.Electronic Vehicle Information Center (EVIC)DisplaysWhen the appropriate conditions

• Service TPM System (with a single chime)• ESP Off – Electronic Stability Control is deactivated• Check Gascap• Key Fob Battery Low• Service Keyless

indicator system is duty cycle based, which means theengine oil change interval may fluctuate, dependentupon your personal driving style.Unless reset,

• Distance To Empty• Trip A• Trip B• Elapsed Time• Display Units of Measure inPress the UP or DOWN button to cycle through the Tripfunctions, press th

Trip AShows the total distance traveled for Trip A since the lastreset.Trip BShows the total distance traveled for Trip B since the lastreset.Elapsed

WARNING! (Continued)limits of the law. The capabilities of the vehicle asmeasured by the performance pages must never beexploited in a reckless or dan

The following describes each feature and its operation:0-60 mph (0-100 km/h)When selected, this screen displays the time it takes forthe vehicle to go

• For vehicles equipped with Keyless Enter-N-Go™,press the Keyless Enter-N-Go™ Start/Stop button(requires at least one valid Key Fob in the vehicle).•

1/8 Mile, 1/4 MileWhen selected, this screen displays the time it takes thevehicle to travel 1/8 mile (1/4 mile) within 30 seconds andthe vehicle’s sp

Digital SpeedometerWhen selected, this screen displays vehicle speed andrecords top speed.• Press and hold the SELECT button for three seconds totoggl

Refer to “Keyless Enter-N-Go™” in “Starting And Oper-ating” for more information.NOTE: Under certain conditions, the display may besuperseded by anoth

also calibrate the compass by completing one or more 360degree turns (in an area free from large metal or metallicobjects) until the “CAL” message dis

1. Turn the ignition switch ON.2. Press and release the MENU button until PersonalSettings displays in the EVIC.3. Press the UP or DOWN button until “

• Tire PressureShows the actual tire pressure for each tire (EXCLUDINGTHE SPARE TIRE).Personal Settings (Customer-ProgrammableFeatures)Personal Settin

Door 1st Press is selected, you must press the RKEtransmitter UNLOCK button twice to unlock the passen-ger door. When All Doors 1st Press is selected,

Headlamps On with Wipers (Available with AutoHeadlights Only)When ON is selected, and the headlight switch is in theAUTO (A) position, the headlights

Delay Power Off to Accessories Until ExitWhen this feature is selected, the power window switches,radio, Uconnect® phone (if equipped), power sunroof(

To make your selection, press and release the SELECTbutton until a check-mark appears next to the featureshowing the system has been activated or the

Security System Manual OverrideThe Vehicle Security Alarm will not arm if you lock thedoors using the manual door lock plunger.ILLUMINATED ENTRYThe co

Uconnect® 130Operating Instructions — Radio ModeNOTE: The ignition switch must be in the ON or ACCposition to operate the radio.Power Switch/Volume Co

another selection. Holding either button will bypassstations without stopping, until you release it.TIME ButtonPress the TIME button to alternate disp

Push the rotary TUNE/SCROLL control knob a secondtime and MID will display. Turn the TUNE/SCROLLcontrol knob to the right or left to increase or decre

display window. Each button can be set for SET 1 andSET 2 in both AM and FM. This allows a total of 12 AMand 12 FM stations to be stored into pushbutt

If you insert a disc with the ignition ON and the radioON, the unit will switch from radio to CD mode andbegin to play when you insert the disc. The d

SEEK ButtonPress the right SEEK button for the next selection on theCD. Press the left SEEK button to return to the beginningof the current selection,

Supported Media (Disc Types)The MP3 file recording media supported by the radio areCDDA, CD-R, CD-RW, MP3, and CDDA+MP3.Supported Medium Formats (File

Supported MP3 File FormatsThe radio will recognize only files with the *.MP3 exten-sion as MP3 files. Non-MP3 files named with the *.MP3extension may

Playback of MP3 FilesWhen a medium containing MP3 data is loaded, theradio checks all files on the medium. If the mediumcontains a lot of folders or f

NOTE: The AUX device must be turned on and thedevice’s volume set to proper level. If the AUX audio isnot loud enough, turn the device’s volume up. If

at speeds 5 mph (8 km/h) and above disables the systemfrom responding to all RKE transmitter buttons for allRKE transmitters.To Unlock The DoorsPress

Power Switch/Volume Control (Rotary)Push the ON/VOLUME control knob to turn on theradio. Push the ON/VOLUME control knob a secondtime to turn off the

Clock Setting Procedure1. Press and hold the TIME button until the hours blink.2. Adjust the hours by turning the right side TUNE/SCROLL control knob.

Setting the Tone, Balance, and FadePush the rotary TUNE/SCROLL control knob and BASSwill display. Turn the TUNE/SCROLL control knob tothe right or lef

Program Type16-Digit CharacterDisplayNo program type orundefinedNoneAdult Hits Adlt HitClassical ClassiclClassic Rock Cls RockCollege CollegeCountry C

station with the same selected Music Type name. TheMusic Type function only operates when in the FMmode.If a preset button is activated while in the M

and 12 FM stations to be stored into pushbutton memory.The stations stored in SET 2 memory can be selected bypressing the pushbutton twice.Every time

If you insert a disc with the ignition ON and the radioON, the unit will switch from radio to CD mode andbegin to play when you insert the disc. The d

SEEK ButtonPress the right SEEK button for the next selection on theCD. Press the left SEEK button to return to the beginningof the current selection,

Supported Media (Disc Types)The MP3 file recording media supported by the radio areCDDA, CD-R, CD-RW, MP3, and CDDA+MP3.Supported Medium Formats (File

Supported MP3 File FormatsThe radio will recognize only files with the *.MP3 exten-sion as MP3 files. Non-MP3 files named with the *.MP3extension may

Remote Key Unlock, Driver Door/All Doors FirstThis feature lets you program the system to unlock eitherthe driver’s door or both doors on the first pr

Playback of MP3 FilesWhen a medium containing MP3 data is loaded, theradio checks all files on the medium. If the mediumcontains a lot of folders or f

Press the INFO button once more to return to ⬙elapsedtime⬙ priority mode.Press and hold the INFO button for three seconds ormore and the radio will di

Radio. This service offers over 130 channels of music,sports, news, entertainment, and programming for chil-dren, directly from its satellites and bro

Selecting Uconnect® Multimedia (Satellite) ModePress the SAT button until ⬙SAT⬙ appears in the display.A CD may remain in the radio while in the Satel

remain tuned to the new channel until you make anotherselection. Holding either button will bypass channelswithout stopping until you release it.SCAN

By pressing the SEEK button when the Music Typefunction is active, the radio will be tuned to the nextchannel with the same selected Music Type name.I

Every time a preset button is used, a correspondingbutton number will display.Buttons1-6These buttons tune the radio to the channels that youcommit to

NOTE: The center console will have a position where theiPod® or consumer electronic audio device cable can berouted through without damaging the cable

NOTE: If the audio device battery is completely dis-charged, it may not communicate with the iPod®/USB/MP3 control system until a minimum charge is at

• Turning it clockwise (forward) by one click, whileplaying a track, skips to the next track or press theVR button and say ⬙Next Track⬙.• Turning it c

•When not using the EVIC, perform the following steps:1. Press and hold the UNLOCK button on a programmedRKE transmitter for at least 4 seconds, but n

SCAN button again. During Scan mode, pressing the<< SEEK and SEEK>> buttons will select the previousand next tracks.• RND button (availabl

• Preset 4 – Genres• Preset 5 – Audiobooks• Preset 6 – Podcasts• Pressing a PRESET button will display the currentlist on the top line and the first i

WARNING!Do not plug in or remove the iPod® or external USBdevice while driving. Failure to follow this warningcould result in an accident.Bluetooth St

Previous TrackUse the SEEK DOWN button, or press the VR button onthe radio and say “Previous Track”, to jump to theprevious music track on your cellul

AUX input; and is activated through the ElectronicVehicle Information Center (EVIC). Refer to “Driver-Selectable Surround Sound (DSS)” under “Electron

The right-hand control is a rocker-type switch with apushbutton in the center and controls the volume andmode of the sound system. Pressing the top of

CD/DVD DISC MAINTENANCETo keep a CD/DVD in good condition, take the followingprecautions:1. Handle the disc by its edge; avoid touching thesurface.2.

CLIMATE CONTROLSAutomatic Temperature Control (ATC)The Automatic Temperature Control system automati-cally maintains the climate in the cabin of the v

You will experience the greatest efficiency by simplyallowing the system to function automatically. Selectingthe “O” (OFF) position on the blower cont

Manual OperationThis system offers a full complement of manual overridefeatures, which consist of Blower Preferred Automatic,Mode Preferred Automatic,

feature. This feature can be turned on or turned off. Referto “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable F

278 UNDERSTANDING YOUR INSTRUMENT PANEL

The operator can override the AUTO mode setting tochange airflow distribution by rotating the Mode Controlknob (right knob) to one of the following po

• Air Conditioner ControlPress this button to turn on the airconditioning during manual operationonly. When the air conditioning isturned on, cool deh

Operating TipsNOTE: Refer to the chart at the end of this section forsuggested control settings for various weather condi-tions.Summer OperationThe en

windshield and provide sufficient heating. If side win-dow fogging becomes a problem, increase blower speed.Vehicle windows tend to fog on the inside

Control Setting Suggestions for Various Weather Conditions while in Manual Override4UNDERSTANDING YOUR INSTRUMENT PANEL 283

STARTING AND OPERATINGCONTENTS䡵 STARTING PROCEDURES ...289▫ Manual Transmission – If Equipped ...289▫ Automatic Transmission – If Eq

䡵 AUTOSTICK® ...311▫ Steering Wheel Mounted Paddle Shifters OrConsole Mounted Shifter ...311䡵 SPORT MODE ...

䡵 TIRE SAFETY INFORMATION ...337▫ Tire Markings ...337▫ Tire Identification Number (TIN)...340▫ Tire Terminolog

the headlights will turn on, the park lights will flash, thehorn will pulse on and off, and the interior lights willturn on.The Panic Alarm will stay

▫ Reformulated Gasoline ...367▫ Gasoline/Oxygenate Blends ...368▫ E-85 Usage In Non-Flex Fuel Vehicles ...368▫ MMT In Gas

STARTING PROCEDURESBefore starting your vehicle, adjust your seat, adjust theinside and outside mirrors, fasten your seat belt, and ifpresent, instruc

Press the clutch pedal fully to the floor, and turn theignition switch to the START position and release whenthe engine starts. If the engine fails to

Using Fob With Integrated Key (Tip Start)NOTE: Normal starting of either a cold or a warmengine is obtained without pumping or pressing theaccelerator

Removing The Button1. The ENGINE START/STOP button can be removedfrom the ignition switch for key fob use.2. Insert the metal part of the emergency ke

3. If you wish to stop the cranking of the engine prior tothe engine starting, release the button.NOTE: Normal starting of either a cold or a warmengi

To Turn Off The Engine Using ENGINESTART/STOP Button – Manual Transmission Only1. With the vehicle stopped, place the shift lever inNEUTRAL, then pres

• Starting with the ignition switch in the OFF position:• Press the ENGINE START/STOP button once tochange the ignition switch to the ACC position (EV

WARNING! (Continued)• If the vehicle has a discharged battery, boostercables may be used to obtain a start from a boosterbattery or the battery in ano

Clearing A Flooded Engine (Using Fob WithIntegrated Key)If the engine fails to start after you have followed the“Normal Starting” or “Extreme Cold Wea

TABLE OF CONTENTSSECTION PAGE1INTRODUCTION ...32THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

2. Remove and replace the battery. When replacing thebattery, match the + sign on the battery to the + sign onthe inside of the battery clip, located

WARNING!Remember to disconnect the engine block heatercord before driving. Damage to the 110-115 Voltelectrical cord could cause electrocution.MANUAL

NOTE: During cold weather, you may experience in-creased effort in shifting until the transmission fluidwarms up. This is normal.ShiftingFully press t

CAUTION!Always make sure the vehicle comes to a completestop before shifting into REVERSE. Failure to do somay result in transmission damage.You must

When the “1–4 Skip Shift Indicator Message” is dis-played, the shift mechanism will only allow shifts fromfirst gear to fourth gear. After you shift t

CAUTION! (Continued)• Shift into or out of REVERSE only after the vehiclehas come to a complete stop and the engine is atidle speed.• Do not shift bet

WARNING! (Continued)• It is dangerous to shift out of PARK or NEUTRALif the engine speed is higher than idle speed. Ifyour foot is not firmly pressing

unless the brakes are applied. To shift the transmissionout of PARK, the ignition switch must be turned to theON/RUN position (engine running or not)

Gear RangesDO NOT race the engine when shifting from PARK orNEUTRAL into another gear range.NOTE:• After selecting any gear range, wait a moment to al

When parking on a level surface, you may place the shiftlever in PARK first, and then apply the parking brake.When parking on a hill, apply the parkin

WARNING! (Continued)• Unintended movement of a vehicle could injurethose in or near the vehicle. As with all vehicles,you should never exit a vehicle

REMOTE STARTING SYSTEM — IF EQUIPPEDThis system uses the Remote Keyless Entry(RKE) transmitter to start the engine conve-niently from outside the vehi

CAUTION!• Before moving the shift lever out of PARK, youmust turn the ignition switch from the OFF posi-tion to the ON/RUN position, and also press th

WARNING! (Continued)practices that limit your response to changing trafficor road conditions. You might lose control of thevehicle and have a collisio

Transmission Limp Home ModeTransmission function is monitored electronically forabnormal conditions. If a condition is detected that couldresult in tr

Overdrive OperationThe automatic transmission includes an electronicallycontrolled Overdrive (fifth gear). The transmission willautomatically shift in

OperationWhen the shift lever is in the DRIVE position, thetransmission will operate automatically, shifting betweenthe five available gears. To engag

• You can start out, from a stop, in first or second gear.Tapping (+) (at a stop) will allow starting in secondgear. Starting out in second gear is he

SPORT MODEThis vehicle is equipped with an electronic controlleddamping system. This system reduces body roll and pitchin many driving situations incl

less aggressive shifting. The system will return to OFFwhen the ignition switch is cycled from RUN to OFF toRUN, if this mode is selected.• Sport Mode

WARNING!Rapid acceleration on slippery surfaces is dangerous.Unequal traction can cause sudden pulling of the rearwheels. You could lose control of th

CAUTION!• Due to lower ground clearance, driving your ve-hicle up steep driveways, approach ramps or nearparking blocks may cause damage to the frontf

WARNING!• Do not start or run an engine in a closed garage orconfined area. Exhaust gas contains Carbon Mon-oxide (CO) which is odorless and colorless

CAUTION! (Continued)• Determine the condition of the road or the paththat is under water and if there are any obstacles inthe way before driving throu

WARNING! (Continued)• Getting water inside your vehicle’s engine cancause it to lock up and stall out, and leave youstranded.• Failure to follow these

CAUTION!Prolonged operation of the steering system at the endof the steering wheel travel will increase the steeringfluid temperature and it should be

When parking on a hill, it is important to turn the frontwheels toward the curb on a downhill grade and awayfrom the curb on an uphill grade. For vehi

Automatic Transmission – If EquippedThe foot operated parking brake is located below thelower left corner of the instrument panel. To apply thepark br

WARNING!• Never use the PARK position as a substitute for theparking brake. Always apply the parking brakefully when parked to guard against vehicle m

CAUTION!If the “Brake Warning Light” remains on with theparking brake released, a brake system malfunctionis indicated. Have the brake system serviced

related motor noises. These noises are the system per-forming its self check cycle to ensure that the ABS systemis working properly. This self check o

WARNING! (Continued)• The Anti-Lock Brake System (ABS) cannot preventthe natural laws of physics from acting on thevehicle, nor can it increase brakin

does not come on when the ignition switch is turned tothe ON position, have the bulb repaired as soon aspossible.If both the “Brake Warning Light” and

To Exit Remote Start Mode Without Driving TheVehiclePress and release the REMOTE START button one time orallow the engine to run for the entire 15-min

WARNING! (Continued)ABS cannot prevent collisions, including those re-sulting from excessive speed in turns, driving onvery slippery surfaces, or hydr

unless braking is no longer desired. Once the brake pedalis released, the BAS is deactivated.WARNING!The BAS cannot prevent the natural laws of physic

WARNING!There may be situations on minor hills (i.e., less than8%), with a loaded vehicle, or while pulling a trailer,when the system will not activat

8. Rotate the steering wheel back to center and then anadditional half-turn to the right.9. Turn the ignition switch to the OFF position and thenback

WARNING! (Continued)accidents, including those resulting from excessivespeed in turns, driving on very slippery surfaces, orhydroplaning. ESC also can

NOTE: To improve the vehicle’s traction when drivingwith snow chains, or when starting off in deep snow,sand, or gravel, it may be desirable to switch

NOTE: The ⬙ESC OFF⬙ message will display and theaudible chime will sound when the shift lever is movedinto the PARK position from any position other t

ESC Activation/Malfunction Indicator Light AndESC OFF Indicator LightThe “ESC Activation/Malfunction IndicatorLight” in the instrument cluster will co

NOTE:• The “ESC Activation/Malfunction Indicator Light”and the “ESC OFF Indicator Light” come on momen-tarily each time the ignition switch is turned

TIRE SAFETY INFORMATIONTire MarkingsNOTE:• P (Passenger) - Metric tire sizing is based on U.S.design standards. P-Metric tires have the letter “P”mold

Cancel Remote StartRemote Starting will also cancel if any of the followingoccur:• The engine stalls or engine speed exceeds 2500 rpm• Any engine warn

compact spare tires have the letter “T” or “S” moldedinto the sidewall preceding the size designation. Ex-ample: T145/80D18 103M.• High flotation tire

EXAMPLE:R = Construction code— ⬙R⬙ means radial construction— ⬙D⬙ means diagonal or bias construction15 = Rim diameter in inches (in)Service Descripti

EXAMPLE:Load Identification:ⴖ...blank...ⴖ = Absence of any text on the sidewall of the tire indicates a Standard Load (SL) tireExtra Load (XL) = Ext

EXAMPLE:DOT MA L9 ABCD 0301DOT = Department of Transportation— This symbol certifies that the tire is in compliance with the U.S. Department of Transp

Tire Terminology And DefinitionsTerm DefinitionB-Pillar The vehicle B-Pillar is the structural member of the body locatedbehind the front door.Cold Ti

Tire Loading And Tire PressureTire And Loading Information Placard LocationNOTE: The proper cold tire inflation pressure is listed onthe driver’s side

Tire And Loading Information PlacardThis placard tells you important information aboutthe:1) number of people that can be carried in the vehicle2) tot

To determine the maximum loading conditions of yourvehicle, locate the statement “The combined weight ofoccupants and cargo should never exceed XXX lb

NOTE:• The following table shows examples on how to calcu-late total load, cargo/luggage, and towing capacitiesof your vehicle with varying seating co

5STARTING AND OPERATING 347

If the door lock knob is down when you shut the door,the door will lock. Therefore, make sure the Key Fob isnot inside the vehicle before closing the

WARNING!Overloading of your tires is dangerous. Overloadingcan cause tire failure, affect vehicle handling, andincrease your stopping distance. Use ti

WARNING! (Continued)• Unequal tire pressures from one side of the vehicleto the other can cause the vehicle to drift to theright or left.• Always driv

Inflation pressures specified on the placard are always“cold tire inflation pressure.” Cold tire inflation pressureis defined as the tire pressure aft

WARNING!High speed driving with your vehicle under maxi-mum load is dangerous. The added strain on yourtires could cause them to fail. You could have

All Season Tires – If EquippedAll Season tires provide traction for all seasons (spring,summer, fall and winter). Traction levels may vary be-tween di

While studded tires improve performance on ice, skidand traction capability on wet or dry surfaces may bepoorer than that of non-studded tires. Some s

Tread Wear IndicatorsTread wear indicators are in the original equipment tiresto help you in determining when your tires should bereplaced.These indic

WARNING!Tires and the spare tire should be replaced after sixyears, regardless of the remaining tread. Failure tofollow this warning can result in sud

WARNING!• Do not use a tire, wheel size or rating other thanthat specified for your vehicle. Some combinationsof unapproved tires and wheels may chang

• Install on Rear Tires Only.• Due to limited clearance, the Security Chain Company(SCC) Super Z6 low profile traction device or equiva-lent is recomm

Power Door LocksThe power door lock switch is located on each door trimpanel. Use this switch to lock or unlock the doors.The doors can also be locked

CAUTION! (Continued)• Observe the traction device manufacturer’s instruc-tions on the method of installation, operatingspeed, and conditions for use.

Tire Rotation – Same tire size on front and rearaxleThe suggested rotation method for vehicles equippedwith all season tires is the “forward-cross” as

TIRE PRESSURE MONITOR SYSTEM (TPMS)The Tire Pressure Monitor System (TPMS) will warn thedriver of a low tire pressure based on the vehicle recom-mende

The vehicle may need to be driven for up to 20 minutesabove 15 mph (24 km/h) in order for the TPMS to receivethis information.For example, your vehicl

NOTE:• The TPMS is not intended to replace normal tire careand maintenance or to provide warning of a tire failureor condition.• The TPMS should not b

• Various TPMS messages, which display in the Elec-tronic Vehicle Information Center (EVIC), and• TPM Telltale LightTire Pressure Monitoring Low Press

Once the system receives the updated tire pressures, thesystem will automatically update, the graphic display inthe EVIC will stop flashing, and the “

longer display, and a pressure value will display in placeof the dashes. A system fault can occur due to any of thefollowing:1. Signal interference du

3. After driving the vehicle for up to 20 minutes above15 mph (24 km/h), the “TPM Telltale Light” will flashon and off for 75 seconds and then remain

FUEL REQUIREMENTS6.4L EngineThe 6.4L engine is designed to meet allemissions regulations and provide excellentfuel economy and performance when usingh

authorized dealer per written request of the customer.Please see your authorized dealer for service.Automatic Unlock Doors On ExitThe doors will unloc

Gasoline/Oxygenate BlendsSome fuel suppliers blend unleaded gasoline with oxy-genates such as Ethanol. Fuels blended with oxygenatesmay be used in you

• disconnect and reconnect the battery to reset theengine controller memoryMore extensive repairs will be required for prolongedexposure to E-85 fuel.

CAUTION! (Continued)• An out-of-tune engine or certain fuel or ignitionmalfunctions can cause the catalytic converter tooverheat. If you notice a pung

WARNING! (Continued)• Guard against carbon monoxide with proper main-tenance. Have the exhaust system inspected everytime the vehicle is raised. Have

CAUTION!• Damage to the fuel system or emissions controlsystem could result from using an improper fueltank filler tube cap (gas cap).• A poorly fitti

Loose Fuel Filler Cap MessageIf the vehicle diagnostic system determines that the fuelfiller cap is loose, improperly installed, or damaged, a“Check G

• Gross Axle Weight Rating (GAWR) rear• Vehicle Identification Number (VIN)• Type of Vehicle• Month Day and Hour of Manufacture (MDH)The bar code allo

Figure out the weight on the front and rear of the vehicleseparately. It is important that you distribute the loadevenly over the front and rear axles

RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.)Towing This Vehicle Behind Another VehicleTowing ConditionWheels OFF TheGroundManual TransmissionAutomatic

CAUTION!Towing this vehicle in violation of the above require-ments can cause severe transmission damage. Dam-age from improper towing is not covered

5. A single chime will indicate the completion of theprogramming.NOTE: If you do not hear the chime, it means that thesystem did not enter the program

WHAT TO DO IN EMERGENCIESCONTENTS䡵 HAZARD WARNING FLASHERS ...380䡵 IF YOUR ENGINE OVERHEATS ...380䡵 TIREFIT KIT ...

HAZARD WARNING FLASHERSThe Hazard Warning flasher switch is located in theswitch bank near the bottom center of the instrumentpanel.Press the switch t

supplement to the radiator and aids in removing heatfrom the engine cooling system.CAUTION!Driving with a hot cooling system could damageyour vehicle.

TIREFIT StorageThe TIREFIT kit is located in the trunk.TIREFIT Kit Components And Operation1. Sealant Bottle2. Deflation Button3. Pressure GaugeTIREFI

4. Power Button5. Mode Select Knob6. Sealant Hose (Clear)7. Air Pump Hose (Black)8. Power PlugUsing The Mode Select Knob And HosesYour TIREFIT kit is

TIREFIT Usage Precautions• Replace the TIREFIT Sealant Bottle (1) and SealantHose (6) prior to the expiration date (printed on thebottle label) to ass

WARNING!• Do not attempt to seal a tire on the side of thevehicle closest to traffic. Pull far enough off theroad to avoid the danger of being hit whe

WARNING! (Continued)•TIREFIT Sealant solution contains latex. In case ofan allergic reaction or rash, consult a physicianimmediately. Keep TIREFIT out

4. Remove the cap from the valve stem and then screwthe fitting at the end of the Sealant Hose (6) onto thevalve stem.5. Uncoil the Power Plug (8) and

door handle to unlock the driver’s door automatically.The interior door panel lock knob will raise when thedoor is unlocked.NOTE: If “Unlock All Doors

NOTE: If the Mode Select Knob (5) is on Air Mode andthe pump is operating, air will dispense from the AirPump Hose (7) only, not the Sealant Hose (6).

3. Immediately disconnect the Sealant Hose (6) from thevalve stem, reinstall the cap on the fitting at the end ofthe hose, and place the TIREFIT kit i

(E) After Driving:Pull over to a safe location. Refer to “Whenever You Stopto Use TIREFIT” before continuing.1. Turn the Mode Select Knob (5) to the A

5. Replace the Sealant Bottle (1) and Sealant Hose (6)assembly at your authorized dealer as soon as pos-sible. Refer to “(F) Sealant Bottle and Hose R

NOTE: When using a portable battery booster packfollow the manufacturer’s operating instructions andprecautions.CAUTION!Do not use a portable battery

WARNING!• Take care to avoid the radiator cooling fan when-ever the hood is raised. It can start anytime theignition switch is ON. You can be injured

CAUTION!Failure to follow these procedures could result indamage to the charging system of the booster vehicleor the discharged vehicle.1. Connect the

8. Disconnect the opposite end of the positive (+) jumpercable from the positive (+) post of the booster battery.9. Disconnect the positive (+) end of

CAUTION! (Continued)the risk of transmission failure during prolongedefforts to free a stuck vehicle.NOTE: Press the ⬙ESC Off⬙ switch, to place the El

SHIFT LEVER OVERRIDEIf a malfunction occurs and the shift lever cannot bemoved out of the PARK position, you can use thefollowing procedure to tempora

Preventing Inadvertent Locking Of Passive Entry RKETransmitter In VehicleTo minimize the possibility of unintentionally locking aPassive Entry RKE tra

TOWING A DISABLED VEHICLEThis section describes procedures for towing a disabledvehicle using a commercial wrecker service.TowingConditionWheels OFFTh

If you must use the accessories (wipers, defrosters, etc.)while being towed, the ignition must be in the ON/RUNposition, not the ACC position.If the v

CAUTION!Towing this vehicle in violation of the above require-ments can cause severe transmission damage. Dam-age from improper towing is not covered

MAINTAINING YOUR VEHICLECONTENTS䡵ENGINE COMPARTMENT — 6.4L (392 HEMI) . .404䡵ONBOARD DIAGNOSTIC SYSTEM — OBD II . . .405▫ Loose Fuel Filler Cap ...

▫ Clutch Hydraulic System(Manual Transmission) – If Equipped ...429▫ Manual Transmission – If Equipped ...429▫ Automatic Transmission – If Eq

䡵FLUIDS, LUBRICANTS AND GENUINE PARTS . .454▫ Engine ...454▫ Chassis ...4557MAINTAINING YOUR VEHICL

ENGINE COMPARTMENT — 6.4L (392 HEMI)1 — Remote Jump Start (Positive Battery Post) 6 — Air Cleaner Filter2 — Engine Oil Dipstick 7 — Power Steering Flu

ONBOARD DIAGNOSTIC SYSTEM — OBD IIYour vehicle is equipped with a sophisticated onboarddiagnostic system called OBD II. This system monitorsthe perfor

Trip Odometer button to turn off the message. If theproblem continues, the message will appear the next timethe vehicle is started.A loose, improperly

4. Approximately 15 seconds later, one of two things willhappen:• The MIL will flash for about 10 seconds and thenreturn to being fully illuminated un

NOTE: If you inadvertently leave your vehicle’s PassiveEntry RKE transmitter in the trunk and try to close thedeck lid, the deck lid will automaticall

available which include detailed service information foryour vehicle. Refer to these Service Manuals beforeattempting any procedure yourself.NOTE: Int

CAUTION! (Continued)• Your vehicle has been built with improved fluidsthat protect the performance and durability of yourvehicle and also allow extend

NOTE: Under no circumstances should oil change in-tervals exceed 6,000 miles (10 000 km) or six months,whichever occurs first.Engine Oil SelectionFor

engine oil. Engine oil is an engineered product and itsperformance may be impaired by supplemental additives.Disposing Of Used Engine Oil And Oil Filt

Engine Air Cleaner Filter SelectionThe quality of replacement engine air cleaner filtersvaries considerably. Only high quality filters should beused t

WARNING!• Battery fluid is a corrosive acid solution and canburn or even blind you. Do not allow battery fluidto contact your eyes, skin, or clothing.

Air Conditioner MaintenanceFor best possible performance, your air conditionershould be checked and serviced by an authorized dealerat the start of ea

Protection Agency and is an ozone-saving product. How-ever, the manufacturer recommends that air conditioningservice be performed by authorized dealer

2. Unsnap both ends and lift the filter access cover.3. Remove the used filter.4. Install the new filter with arrows pointing in thedirection of airfl

Body LubricationLocks and all body pivot points, including such items asseat tracks, door hinge pivot points and rollers, liftgate,tailgate, sliding d

Do NOT grab the door handle, when pressing the doorhandle lock button. This could unlock the door(s).NOTE:• After pressing the door handle LOCK button

Adding Washer FluidThe windshield washer fluid reservoir is located in thefront of the engine compartment. Be sure to check thefluid level in the rese

have an authorized technician inspect the complete ex-haust system and adjacent body areas for broken, dam-aged, deteriorated, or mispositioned parts.

CAUTION! (Continued)• Damage to the catalytic converter can result if yourvehicle is not kept in proper operating condition.In the event of engine mal

Cooling SystemWARNING!• When working near the radiator cooling fan,disconnect the fan motor lead or turn the ignitionswitch to the LOCK position (OFF

properly, the engine coolant (antifreeze) will begin todrain from the coolant recovery bottle. DO NOT RE-MOVE THE COOLANT PRESSURE CAP WHEN THECOOLING

CAUTION! (Continued)• Do not use water alone or alcohol-based enginecoolant (antifreeze) products. Do not use additionalrust inhibitors or antirust pr

(antifreeze) solution. The use of lower quality waterwill reduce the amount of corrosion protection in theengine cooling system.Please note that it is

Disposal Of Used Engine CoolantUsed ethylene glycol-based engine coolant (antifreeze) isa regulated substance requiring proper disposal. Checkwith you

• Do not overfill the coolant expansion bottle.• Check the coolant freeze point in the radiator and inthe coolant expansion bottle. If engine coolant

WARNING!Riding the brakes can lead to brake failure andpossibly a collision. Driving with your foot resting orriding on the brake pedal can result in

There is a single window control on the passenger’s doortrim panel that operates the window on the passenger’sdoor. The window controls will operate o

WARNING!• Use only manufacturer’s recommended brakefluid. Refer to “Fluids, Lubricants, and GenuineParts” in “Maintaining Your Vehicle” for furtherinf

WARNING! (Continued)• Do not allow petroleum based fluid to contaminatethe brake fluid. Brake seal components could bedamaged, causing partial or comp

Automatic Transmission – If EquippedSelection Of LubricantIt is important to use the proper transmission fluid toensure optimum transmission performan

CAUTION!Do not use chemical flushes in your transmission asthe chemicals can damage your transmission compo-nents. Such damage is not covered by the N

Rear AxleFluid Level CheckChecking the fluid level while the vehicle is on levelground will improve the accuracy of the fluid levelreading.Check the f

What Causes Corrosion?Corrosion is the result of deterioration or removal ofpaint and protective coatings from your vehicle.The most common causes are

Special Care• If you drive on salted or dusty roads or if you drivenear the ocean, hose off the undercarriage at least oncea month.• It is important t

CAUTION!Do not use scouring pads, steel wool, a bristle brush,or metal polishes. Do not use oven cleaner. Theseproducts may damage the wheel’s protect

Interior Trim should be cleaned starting with a dampcloth, or MOPAR® Satin Select or equivalent. Do not useharsh cleaners or Armor All®. Use MOPAR® To

Glass SurfacesAll glass surfaces should be cleaned on a regular basiswith MOPAR® Glass Cleaner or any commercialhousehold-type glass cleaner. Never us

WARNING!Never leave children unattended in a vehicle, and donot let children play with power windows. Do notleave the key fob in or near the vehicle,

Cleaning The Center Console CupholdersClean with a damp cloth or towel using a mild detergentwith the cupholder in the center console.NOTE: The cuphol

CAUTION!• When installing the integrated power modulecover, it is important to ensure the cover is properlypositioned and fully latched. Failure to do

Cavity Car-tridgeFuseMini-FuseDescription8 — 30 AmpGreenStarter9—— —10 30 AmpPink— Windshield Wiper11 30 AmpPink— Anti-Lock BrakeSystem (ABS)Valves12

Rear Power Distribution CenterThere is also a power distribution center located in thetrunk under the spare tire access panel. This centercontains fus

Cavity Car-tridgeFuseMini-FuseDescription1 60 AmpYellow— Ignition Off Draw(IOD)Cavity 1 of theRear Power Distri-bution Center con-tains a black IODfus

Cavity Car-tridgeFuseMini-FuseDescription8 — 15 AmpBlueDiagnostic LinkConnector (DLC)/Wireless ControlModule (WCM)/Wireless IgnitionNode (WIN)9 — 20 A

Cavity Car-tridgeFuseMini-FuseDescription20 — — —21 — — —22 — — —23 — — —24 — — —25 — — —26 — — —27 — 10 AmpRedOccupant RestraintController (ORC)28 —

Cavity Car-tridgeFuseMini-FuseDescription35 — 5 AmpOrangeAntenna Module –If Equipped/PowerMirrors36 — 25 AmpNaturalHands-FreePhone – IfEquipped/Radio/

the 25 Amp circuit breaker in cavity 11. The passengerseat switch is fused by the 25 Amp circuit breaker incavity 12. The door modules, the driver pow

Bulb NumberVisor Vanity Lamps A6220Glove Box Lamp –If Equipped194Door Courtesy 562Shift Indicator Lamp JKLE14140Optional Door MapPocket/CupholderLED (

Wind BuffetingWind buffeting can be described as the perception ofpressure on the ears or a helicopter-type sound in theears. Your vehicle may exhibit

BULB REPLACEMENTLow Beam Headlamp, High Beam Headlamp,Park/Turn Lamp — Models with HalogenHeadlamps — If EquippedSee your authorized dealer for bulb r

Front/Rear Side Marker Lamp1. Remove the front/rear side marker. Use a fiber stick orsimilar tool to gently pry the lamp on the outboardside to diseng

3. Remove the fasteners from the back of the tail lampassembly.4. Pull back the trunk liner.5. Remove the remaining fasteners from the back of thetail

10. Disconnect the bulb from the socket assembly andinstall the replacement bulb.11. Reinstall the bulb and socket assembly into the taillamp assembly

Center High-Mounted Stop Lamp (CHMSL)The CHMSL uses LED lamps that are not serviceableseparately. The CHMSL must be replaced as an assembly,see your a

FLUID CAPACITIESU.S. MetricFuel (Approximate) 19 Gallons 72 LitersEngine Oil With Filter6.4 Liter Engine (SAE 0W-40, Synthetic API Certified) 7 Quarts

FLUIDS, LUBRICANTS AND GENUINE PARTSEngineComponent Fluid, Lubricant, or Genuine PartEngine Coolant We recommend you use MOPAR® Antifreeze/Coolant 10

ChassisComponent Fluid, Lubricant, or Genuine PartManual Transmission –If EquippedWe recommend you use MOPAR® ATF+4® Automatic TransmissionFluid.Autom

MAINTENANCE SCHEDULESCONTENTS䡵 MAINTENANCE SCHEDULE ...458▫ Required Maintenance Intervals ...4608MAINTENANCESCHEDULES

With the ignition switch in the ON/RUN position, theTrunk Open symbol will display in the instrument clusterindicating that the trunk is open. The odo

MAINTENANCE SCHEDULEThe Scheduled Maintenance services listed in thismanual must be done at the times or mileages specifiedto protect your vehicle war

Your authorized dealer will reset the oil change indicatormessage after completing the scheduled oil change. If ascheduled oil change is performed by

CAUTION!Failure to perform the required maintenance itemsmay result in damage to the vehicle.Required Maintenance IntervalsRefer to the Maintenance Sc

6,000 Miles (10,000 km) or6 Months Maintenance ServiceSchedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.Odometer Reading DateRepair

18,000 Miles (30,000 km) or18 Months Maintenance ServiceSchedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.❏ Inspect the rear axle fl

30,000 Miles (50,000 km) or30 Months Maintenance ServiceSchedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.❏ Replace the engine air c

42,000 Miles (70,000 km) or42 Months Maintenance ServiceSchedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.Odometer Reading DateRepai

48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule❏ Change the engine oil and engine oil filter.❏ Rotate tires.❏ If you are using your

54,000 Miles (90,000 km) or54 Months Maintenance ServiceSchedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.❏ Inspect the rear axle fl

66,000 Miles (110,000 km) or66 Months Maintenance ServiceSchedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.Odometer Reading DateRepa

OCCUPANT RESTRAINTSSome of the most important safety features in yourvehicle are the restraint systems:• Three-point lap and shoulder belts for the dr

78,000 Miles (130,000 km) or78 Months Maintenance ServiceSchedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.Odometer Reading DateRepa

90,000 Miles (150,000 km) or90 Months Maintenance ServiceSchedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.❏ Replace the engine air

102,000 Miles (170,000 km) or102 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.Odometer Reading DateRe

114,000 Miles (190,000 km) or114 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.Odometer Reading DateRe

120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule❏ Change the engine oil and engine oil filter.❏ Rotate tires.❏ Replace the engine

126,000 Miles (210,000 km) or126 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.❏ Inspect the rear axle

138,000 Miles (230,000 km) or138 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.Odometer Reading DateRe

144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule❏ Change the engine oil and engine oil filter.❏ Rotate tires.❏ If you are using y

150,000 Miles (250,000 km) or150 Months MaintenanceService Schedule❏ Change the engine oil and engine oilfilter.❏ Rotate tires.❏ Replace the engine ai

* This maintenance is recommended by the manufacturerto the owner, but is not required to maintain emissionswarranty.WARNING!• You can be badly injure

all the way out and then adjusting the belt to thedesired length to restrain a child seat or secure a largeitem in a seat — if equippedPlease pay clos

IF YOU NEED CONSUMER ASSISTANCECONTENTS䡵 SUGGESTIONS FOR OBTAINING SERVICEFOR YOUR VEHICLE ...481▫ Prepare For The Appointment...

䡵 DEPARTMENT OF TRANSPORTATIONUNIFORM TIRE QUALITY GRADES ...487▫ Treadwear...487▫ Traction Grades ...

SUGGESTIONS FOR OBTAINING SERVICE FORYOUR VEHICLEPrepare For The AppointmentIf you are having warranty work done, be sure to havethe right papers with

facilities, factory-trained technicians, special tools, andthe latest information to ensure the vehicle is fixedcorrectly and in a timely manner.This

In Mexico contact:Av. Prolongacion Paseo de la Reforma, 1240Sante Fe C.P. 05109Mexico, D. F.In Mexico City: 5081-7568Outside Mexico City: 1-800-505-13

The manufacturer will not stand behind any servicecontract that is not the manufacturer’s service contract.It is not responsible for any service contr

MOPAR® PARTSMOPAR® fluids, lubricants, parts, and accessories areavailable from an authorized dealer. They are recom-mended for your vehicle in order

PUBLICATION ORDER FORMSTo order the following manuals, you may use either thewebsite or the phone numbers listed below. Visa, Mas-tercard, American Ex

Call toll free at:• 1–800–890–4038 (U.S.)• 1–800–387–1143 (Canada)OrVisit us on the Worldwide Web at:• www.techauthority.comDEPARTMENT OF TRANSPORTATI

children to slide the shoulder belt behind them or undertheir arm.If a child from 1 to 12 years old (not in a rear facing childseat) must ride in the

WARNING!The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does notinclude acceleration, cornering, hydrop

INDEX10

About Your Brakes ...320ABS (Anti-Lock Brake System) ...324Adding Engine Coolant (Antifreeze) ...423Adding

Automatic Transmission ...304Adding Fluid ...431Fluid and Filter Changes ...431Fluid Change ...

Calibration, Compass ...231Capacities, Fluid ...453Caps, FillerFuel ...371Oil

Adding Coolant (Antifreeze) ...423Coolant Capacity ...453Coolant Level ...421Disposal of Used C

Electrical Power Outlets...194Electric Remote Mirrors ...108Electronic Brake Control System ...327Anti

Starting ...289Temperature Gauge ...209Engine Oil Viscosity ...410Enhanced Accident

Additives ...369Clean Air ...367Ethanol ...368Filler Cap (Gas Cap) ...

Hazard Warning Flasher ...380Headlights ...448Automatic ...158Cleaning ...

INTRODUCTIONCONTENTS䡵 INTRODUCTION ...4䡵 HOW TO USE THIS MANUAL ...4䡵 WARNINGS AND CAUTIONS ...6䡵 VEHICLE I

WARNING! (Continued)• Being too close to the steering wheel or instrumentpanel during Advanced Front Air Bag deploymentcould cause serious injury, inc

Jump Starting ...391Key-In Reminder ...16Keyless Enter-N-Go ...36Keyless Entry Sy

Engine Temperature Warning ...211Exterior ...100Fog ...160Hazard Warning Flasher

Locks ...32Automatic Door ...34Auto Unlock ...35Door ...

Odometer...208Trip...208Oil Change Indicator ...222Oil Change Indicator,

Deck Lid Release ...43Distribution Center (Fuses) ...441Door Locks ...34Mirrors ...

Replacement Bulbs ...446Replacement Keys ...18Replacement Parts...407Replacement Tire

Rear Folding ...154Seatback Release ...154Tilting ...147Security Alarm (Theft

Starting ...29Automatic Transmission ...290Cold Weather ...295Engine Fails to Star

Tires ...100Aging (Life of Tires) ...354Air Pressure ...348Chains ...

Transmitter Programming (Remote Keyless Entry) . . .22Transmitter, Remote Keyless Entry (RKE) ...22Tread Wear Indicators ...3

Lap/Shoulder BeltsAll seating positions in your vehicle are equipped withlap/shoulder belts.The belt webbing retractor is designed to lock duringvery

Wheel and Wheel Trim ...434Wheel and Wheel Trim Care ...434Wind Buffeting...43Window Fogging

INSTALLATION OF RADIO TRANSMITTINGEQUIPMENTSpecial design considerations are incorporated into thisvehicle’s electronic system to provide immunity to

Challenger13D492-126-AD4th EditionPrinted in U.S.A.Chrysler Group LLC

WARNING! (Continued)• Wearing your belt in the wrong place could makeyour injuries in a collision much worse. You mightsuffer internal injuries, or yo

3. When the belt is long enough to fit, insert the latchplate into the buckle until you hear a “click.”Latch Plate Latch Plate To Buckle2THINGS TO KNO

WARNING!•A belt that is buckled into the wrong buckle willnot protect you properly. The lap portion could ridetoo high on your body, possibly causing

4. Position the lap belt across your thighs, below yourabdomen. To remove slack in the lap belt portion, pullup a bit on the shoulder belt. To loosen

6. To release the belt, push the red button on the buckle.The belt will automatically retract to its stowed posi-tion. If necessary, slide the latch p

Restraints” section. The chart below defines the type offeature for each seating position.Driver Center PassengerFirst Row N/A N/A ALRSecond Row ALR A

2. Grasp the shoulder portion and pull downward untilthe entire belt is extracted.3. Allow the belt to retract. As the belt retracts, you willhear a c

These devices may improve the performance of the seatbelt by assuring that the belt is tight about the occupantearly in a collision. Pretensioners wor

INTRODUCTIONCongratulations on selecting your new Chrysler GroupLLC vehicle. Be assured that it represents precisionworkmanship, distinctive styling,

equipped). It is recommended that pets be restrained inthe rear seat in pet harnesses or pet carriers that aresecured by seat belts, and cargo is prop

WARNING! (Continued)low and snug and in the recommended seating posi-tions. Remove and store the extender when notneeded.Supplemental Restraint System

The Advanced Front Air Bags have a multistage inflatordesign. This allows the air bag to have different rates ofinflation based on several factors, in

• Steering Wheel and Column• Instrument Panel• Knee Impact Bolster• Driver Advanced Front Air Bag• Passenger Advanced Front Air Bag• Supplemental Seat

WARNING! (Continued)• Do not put anything on or around the air bagcovers or attempt to open them manually. You maydamage the air bags and you could be

Supplemental Side Air Bag Inflatable Curtain(SABIC)SABIC air bags may offer side-impact protection to frontand rear seat outboard occupants in additio

• Being too close to the SAB and SABIC air bags duringdeployment could cause you to be severely injured orkilled.The system includes side impact senso

SAB and SABIC air bags are a supplement to the seat beltrestraint system. Occupants, including children who areup against or very close to SAB or SABI

Advanced Front Air Bags and Supplemental Driver KneeAir Bag are designed to provide additional protection bysupplementing the seat belts in certain fr

The ORC contains a backup power supply system thatmay deploy the air bags even if the battery loses power orit becomes disconnected prior to deploymen

1INTRODUCTION 5

Advanced Front Air Bags. Different air bag inflation ratesare possible, based on several factors, including thecollision type and severity. The steeri

and type of collision. In these events, the ORC willdeploy the SABIC only on the impact side of the vehicle.A quantity of non-toxic gas is generated t

In order to reset the Enhanced Accident Response Systemfunctions after an event, the ignition switch must bechanged from IGN ON to IGN OFF.If A Deploy

Do not drive your vehicle after the air bags have de-ployed. If you are involved in another collision, the airbags will not be in place to protect you

WARNING! (Continued)• Do not attempt to modify any part of your air bagsystem. The air bag may inflate accidentally or maynot function properly if mod

NOTE: If the speedometer, tachometer, or any enginerelated gauges are not working, the Occupant RestraintController (ORC) may also be disabled. The ai

In addition to the vehicle manufacturer, other parties,such as law enforcement, that have the special equip-ment, can read the information if they hav

WARNING! (Continued)hold even an infant on your lap could become sogreat that you could not hold the child, no matterhow strong you are. The child and

Child Size, Height, Weight or AgeRecommended Type of ChildRestraintSmall Children Children who are at least twoyears old or who have out-grownthe heig

The infant carrier is only used rearward-facing in thevehicle. It is recommended for children from birth untilthey reach the weight or height limit of

WARNINGS AND CAUTIONSThis Owners Manual contains WARNINGS against oper-ating procedures that could result in a collision or bodilyinjury. It also cont

remain in a forward-facing child seat with a harness foras long as possible, up to the highest weight or heightallowed by the child seat.All children

Children Too Large For Booster SeatsChildren who are large enough to wear the shoulder beltcomfortably, and whose legs are long enough to bendover the

Recommendations For Attaching Child RestraintsRestraint Type CombinedWeight of theChild + ChildRestraintUse any attachment method shown with an “X” Be

Lower Anchors and Tethers for Children (LATCH)Restraint SystemYour vehicle is equipped with the child restraint anchor-age system called LATCH, which

LATCH Positions For Installing Child Restraints InThis VehicleLower Anchorage Symbol 2 anchorages per seatingpositionTop Tether Anchorage Symbol82 THI

What is the weight limit (child’sweight + weight of the childrestraint) for using the LATCHanchorage system to attach thechild restraint?65 lbs (29.5

Can two child restraints beattached using a common lowerLATCH anchorage?No Never “share” a LATCH anchoragewith two or more child restraints.If the cen

Locating The LATCH AnchoragesThe lower anchorages are round bars that arefound at the rear of the seat cushion where itmeets the seatback, below the a

window. These tether strap anchorages are under aplastic cover with the tether anchorage symbol on it.LATCH-compatible child restraint systems will be

Always follow the directions of the child restraint manu-facturer when installing your child restraint. Not all childrestraint systems will be install

NOTE: It is illegal to remove or alter the VIN.VEHICLE MODIFICATIONS/ALTERATIONSWARNING!Any modifications or alterations to this vehicle couldseriousl

7. Test that the child restraint is installed tightly bypulling back and forth on the child seat at the beltpath. It should not move more than 1 inch

Installing Child Restraints Using The Vehicle SeatBeltThe seat belts in the passenger seating positions areequipped with either a Switchable Automatic

What is the weight limit (child’sweight + weight of the childrestraint) for using the TetherAnchor with the seat belt to attacha forward facing child

Installing A Child Restraint with a SwitchableAutomatic Locking Retractor (ALR)1. Place the child seat in the center of the seatingposition. For some

8. If the child restraint has a top tether strap and theseating position has a top tether anchorage, connectthe tether strap to the anchorage and tigh

4. Finally, pull up on any excess webbing to tighten thelap portion around the child restraint while you pushthe child restraint rearward and downward

Installing Child Restraints Using The Top TetherAnchorageLook behind the seating position where youplan to install the child restraint to find theteth

1 — Cover A — Tether Strap Hook3 — Attaching Strap B — Tether Anchor3. Attach the tether strap hook of the child restraint tothe top tether anchorage

While cruising, brief full-throttle acceleration within thelimits of local traffic laws contributes to a good break-in.However, wide-open throttle acc

WARNING! (Continued)• It is extremely dangerous to ride in a cargo area,inside or outside of a vehicle. In a collision, peopleriding in these areas ar